Troubleshooting
Alerts & Display Indicators
Vessel Not Installed Alert: All preset LEDs are flashing.
The unit has detected that the drink vessel is not properly seated or locked onto the motor base.
1. To Resolve: Press the Power button to turn off the unit. To prevent spills, ensure the vessel is empty before adjusting. With the bail handle pulled forward/up, slide the vessel over the installed auger and evaporator. Lock the vessel in place by pushing the bail handle all the way back to seal. Press the Power button on; the preset LEDs will illuminate steadily.
Low-Sugar Alert: "ADD SUGAR" LED is illuminated, and the unit beeps every minute.
Your recipe contains too little sugar to slush properly. Every ingredient input must contain at least 5g of sugar per 100ml. Sugar-free substitutes or artificial sweeteners do not count toward this minimum.
1. To Resolve: For every 230ml of liquid in the vessel, add 2 tablespoons (30ml) of simple syrup, flavoured syrup, honey, agave nectar, maple syrup, or fruit juice. If using granulated sugar, dissolve it in 230ml of liquid before adding it back. Press the program button again to clear the alert and resume slushing.
2. Diet/Zero-Sugar Drinks: Follow the specific diet recipe chart in your manual (adding erythritol, lemon juice, and salt) to enable zero-sugar drinks to slush.
High-Alcohol / High-Sugar Alert: "ADD WATER" LED is illuminated, and the unit beeps every minute.
The alcohol or sugar content in your drink is too high, preventing the liquid from slushing or freezing properly.
1. Alcohol Guidelines: When using the FROZEN COCKTAIL preset, alcohol content must be between 2.8% and 15%. When using FROZEN COCKTAIL MAX, alcohol content must be between 15% and 20%. For hard spirits (35%+ ABV), do not exceed 120ml of spirits per 710ml total recipe size.
2. To Resolve: Add 3 tablespoons (45ml) of water per 230ml serving (or 160ml water per 800ml total recipe) to dilute the mixture. Press the active program button again to clear the error and continue slushing.
Motor Stall Alert: Every Temperature Control LED is flashing, and the unit beeps every minute.
The motor encountered severe resistance and disabled itself to prevent damage.
1. To Resolve: Unplug the unit from the power point and allow it to cool for approximately 15 minutes. Plug it back in and select a program. If the error persists, unplug again, remove the vessel and auger, and verify that there are no hard objects or frozen blocks jamming the auger.
2. Important Safety Warning: This unit is not a blender. Never add solid ice cubes, blocks of ice, frozen fruit, or hot ingredients to the vessel.
Unit Sideways Alert: The top 5 and bottom 5 Temperature Control LEDs flash alternately, and the unit beeps every minute.
The unit detected that it was tipped or placed on its side, which can damage the internal refrigeration compressor.
1. To Resolve: Place the unit upright on a flat, level surface. Do not turn the unit on immediately. You must let the unit stand upright for at least 2 hours before plugging it in and operating to allow the refrigerant oils to fully settle in the condenser.
Unit Failure Alert: Every other Temperature Control LED flashes alternately, and the unit beeps every minute.
An internal system error has occurred.
1. To Resolve: Turn off and unplug the unit immediately.
The auger stops and the screen flashes "SENSING".
1. This is part of normal operation when using the SLUSHASSIST program. The unit is actively calculating the temperature and texture required for your drink. Allow the process to complete without intervening; the unit will correct itself and resume slushing once calculated.
Slushing & Dispensing Performance
My recipe is not slushing, even after 60 minutes.
1. Adjust Temperature Control: Turn the temperature dial clockwise one notch to set a colder temperature. Wait 5 to 10 minutes to test the texture. Repeat by turning the dial clockwise one more level if needed.
2. Check Sugar Levels: Confirm your recipe meets the minimum required sugar content of 5g per 100ml. Pre-chilling your liquids before pouring them into the easy-fill port will also speed up slushing.
The slush is not dispensing smoothly.
1. To Resolve: Ensure the liquid level in the vessel meets the minimum requirement of 710ml (maximum capacity is 3310ml) and that the unit is running. If the slush is too thick or frozen to flow out easily, turn the temperature dial anticlockwise one notch to adjust to a warmer, more sippable texture.
Cleaning & Storage
How do I clean and store my SLUSHi™ MAX?
Always run a Rinse Cycle before disassembling for hand-washing. Never submerge the motor base in water or wash parts in a dishwasher with a heated dry cycle.
1. Using the Rinse Cycle: Dispense any remaining drink. Press the RINSE button and add hot water up to the vessel's max fill line (3310ml). Slowly pull the handle to dispense the rinse water into a large container. Press RINSE again, leave the top cover open to air-dry, and press the Power button to turn off.
2. Disassembly & Washing: Unlock the bail handle by pulling it forward, gently slide the vessel off (tip it downward to avoid liquid spilling out the back), and slide the auger off the evaporator. Slide out the condensation catch. Hand-wash all removable parts in warm, soapy water. Wipe down the metal evaporator and motor base with a warm, damp cloth.
3. Storage: Allow all parts to air-dry completely before reassembling. Store the unit upright with the drip tray stored on the left side of the base. Do not carry the unit by the bail handle, always lift from the bottom of the motor base.





