Troubleshooting
Remote Control & UI Display Issues
Why is the remote control not working?
1. Direct Line of Sight: Ensure you are pointing the remote directly at the LED display panel on the front of the fan head.
2. Battery Saver Tab: If using for the first time, check that the plastic battery saver pull-tab has been removed from the remote’s battery compartment.
3. IDLE Mode Active: To preserve battery life, the fan enters IDLE Mode if left unplugged and powered off for 24 hours. In IDLE Mode, the remote cannot turn the fan on. To exit IDLE Mode, press the physical Power Button on top of the fan head.
4. Remote Re-Pairing Instructions:
- Press and hold the Power Button on top of the fan head for 5 seconds until the LEDs begin flashing.
- While the LEDs are flashing, press the Fan Speed Up (Right Arrow / ^) button on the remote control.
- If it still does not connect, replace the 2x AAA batteries in the remote and repeat the connection process.
Why are the remote and UI buttons completely unresponsive?
1. Lock Mode Active: If all LEDs are flashing or unresponsive, the fan may be in Lock Mode (a safety setting that blocks all functions during maintenance to prevent accidental activation).
2. To Deactivate Lock Mode: Press and hold the Oscillation icon on top of the fan head for 8 seconds. Once Lock Mode is deactivated, the display will show the standard Power On animation.
Battery, Charging & BreezeBoost™ Modes
Why is the battery light flashing red when trying to turn on BreezeBoost™ mode?
1. Low Battery Level: BreezeBoost™ mode requires higher power output. If the battery charge is low, BreezeBoost™ mode cannot be activated. Charge the fan battery to use BreezeBoost™.
2. Note: When operating cordlessly, BreezeBoost™ will automatically turn off after 20 minutes to conserve battery power. When plugged into a power point, it will run indefinitely.
Understanding Battery Status & LED Light Indicators
1. 70% - 100%: Solid Green Light.
2. 30% - 69%: Solid Amber Light.
3. 6% - 29%: Solid Red Light.
4. 5% and below: Blinking Red Light (Charge immediately).
5. Charging Display: While charging, the battery LED will blink green. A full charge from 0% to 100% takes approximately 5 to 6 hours.
Charging Safety & Power Requirements
1. Charger Types: Use only the supplied power supply
2. Outdoor Charging Warning: When used outdoors, connect the power cord only to a covered, RCD-protected power point. DO NOT charge or use the fan cord in the rain, and never handle electrical plugs near the misting stream.
Outdoor Misting System & Water Tank Maintenance
Safety Warning for Misting
1. Outdoor Use Only: The integrated misting feature is suitable for OUTDOOR USE ONLY. Do not attempt to mist indoors, as it will cause slippery floor conditions or water damage. Never mist substances other than cold or room-temperature filtered/clean tap water.
Why isn't the fan misting effectively or producing mist?
1. Check Connections: Ensure the misting hose is securely connected to the back of the water tank (turned clockwise) and to the back of the fan head (turned anticlockwise).
2. Clogged Misting Nozzles: Mineral deposits can restrict mist flow. Clean the nozzles every 12 months (or more frequently with hard water):
- Carefully remove each brass nozzle by turning it anticlockwise by hand (DO NOT use wrenches or metal tools).
- Soak the nozzles in a solution of undiluted distilled white vinegar (5% acetic acid) for up to 2 hours to loosen scale and debris.
- Rinse the nozzles thoroughly with clean water and hand-tighten them clockwise back into place.
3. Clogged Water Tank Filter: Inspect the water tank filter. If the issue persists after cleaning the nozzles, visit sharkclean.com.au or sharkclean.co.nz to order a replacement filter.
Why does the mist feel too wet?
1. Lower the Misting Setting: Press the Misting icon on the remote or fan head to cycle through the 3 misting settings:
- Setting 1: High-Pressure Consistent (maximum cooling).
- Setting 2: Low-Pressure Consistent (balanced cooling and duration).
- Setting 3: Low-Pressure Interval (longest misting duration).
2. Adjust Airflow: Increasing the fan speed helps disperse the mist particles more thoroughly before they land.
3. Distance: Moving a few metres back from the fan head improves the cooling effect without wetting clothing or surfaces.
Fan Care & Noise Troubleshooting
Why is the fan making a rattling noise?
1. Loose Fan Blade Cap: Ensure the fan blade cap is completely tightened.
2. Tightening Procedure: Activate Lock Mode (hold Oscillation button for 8 seconds), remove the Phillips-head screw at the bottom of the front fan grill using the included Allen wrench/driver, rotate the grill anticlockwise to remove it, hold the blades in place, and turn the centre blade cap anticlockwise to ensure it is firmly secured onto the shaft.
How should I prepare the fan for short-term or long-term storage?
1. Drain Internal Lines: Remove, empty, and dry the water tank and misting hose. Disconnect the hose from the fan head and water tank, then run the misting system for 20 seconds to flush out any stagnant water remaining in the internal lines. Store the fan indoors out of reach of children and pets.





